HOT WORK PERMIT PROCEDURE PDF



Hot Work Permit Procedure Pdf

PERMIT TO WORK SYSTEM Kimberley Ports Authority. Safe Operating Procedure (Revised 10/17) HOT WORK PERMIT OPERATIONS _____ Authority . In recognition of the inherent hazards posed by certain hot work processes, the National Fire Protection Agency adopted Standard 51B, Standard for Fire Prevention During, PERMIT TO WORK SYSTEM File ref: OSH047/92460 Version: 5.4 Issue date: July 2017 Page 4 of 10 Table 1: Permit to Work types KPA PERMITS are Compulsory for the following prohibited activities. All Vessels in Port Waters Third Party Contractors KPA jurisdiction KPA Works Bunkering Permit Hot Work Permit.

Safe Operating Procedure University of Nebraska–Lincoln

Hotwork & Welding OSHA Safety Program SafetyInfo. Appendix R – Standard Operating Procedure for Hot Works University of Minnesota, Facilities Management November 2002 (Revised: December 2006) Page 3 of 15 5.1. After the final check, Part 2 of the permit shall be filed at the same location as Part 1., Appendix R – Standard Operating Procedure for Hot Works University of Minnesota, Facilities Management November 2002 (Revised: December 2006) Page 3 of 15 5.1. After the final check, Part 2 of the permit shall be filed at the same location as Part 1..

PROCEDURE 4.0—HOT WORK PROGRAM 4.1 INTRODUCTION Purpose Regulations promulgated by the Occupational Safety and Health Administration (OSHA—29 CFR 1910.252—Welding, Cutting and Brazing) and the NYS Office of Fire Prevention and Control (OFPC—NYS Fire Code Chapter 26—Hot Work) require facilities to develop procedures to protect 2. Obtain a “Hot Work Permit” from a Permit Issuer prior to commencing hot work operations. 3. Display the “Hot Work Permit” at, or in close proximity to, the area where the hot work is being carried out. 4. Continually monitor and review the work site and cease hot work if unsafe conditions develop. 5. Know the procedure for sounding

“A hot work permit procedure, which may be part of an overarching safe system of work/permit to work procedure, should be followed before any hot work is allowed in or near a building. This is to ensure that correct actions are taken before hot work commences, during the operation and afterwards.” No hot work is permitted without authorization, in the form of a signed hot work permit. This This permit will be valid for a maximum of one shift, or eight hours, whichever is shorter.

No hot work is permitted without authorization, in the form of a signed hot work permit. This This permit will be valid for a maximum of one shift, or eight hours, whichever is shorter. Hot Work Permit. Permit No. This permit must be completed for all cutting, welding and other hot work performed outside a dedicated workshop area. The permit must be displayed at the work site and returned to the authorised site representative on completion of work for sign off and filing. Application for hot work Company/Dept Performing Work

The Authorised Person shall then receipt and acknowledgement of the closed off hot work permit. The completed Permit shall be returned to the relevant AreaManager or delegate for record keeping. 3 People 3.1 Training All personnel authorised to issue Hot Work Permits shall have been trained as competent in the hot work permit procedures All hot work is by permit only. Prior to hot work, the HW authorising officer must document on the permit: • the date of the hot work; • the permit expiry time; and • the control measures that were identified during the risk assessment. The type of hot work and the control measures are included in sections 1 to 15 of the hot work permit

Generator’s Permit to Work Code of Practice. This Manual outlines the key elements of this system such as roles and responsibilities, procedures, training, reporting and monitoring activities. Copies of this company-wide manual are available at each CS Energy site. It is also included on Warning! hot work permit. All temporary operations involving open flames or producing heat and/or sparks require a Hot Work Permit. This includes, but is not limited to, Brazing, Cutting, Grinding, Welding, Thawing, and Soldering.

Hot Work Policy & Procedure Policy: The purpose of the PCS General Contractor Hot Work policy is to protect personnel and property from a fire caused by hot work. The PCS Hot Work procedure defines the responsibilities and requirements for performing hot work and establishes controls through the use of a hot work permit. This procedure establishes the means to assess the work area and the All hot work is by permit only. Prior to hot work, the HW authorising officer must document on the permit: • the date of the hot work; • the permit expiry time; and • the control measures that were identified during the risk assessment. The type of hot work and the control measures are included in sections 1 to 15 of the hot work permit

Fire Prevention Hot Work Procedures Stanford University

Hot work permit procedure pdf

PRO-4.5-0001-1-01 Permit to Work. Hot Works Operations Policy Introduction: Purpose To establish procedures defining a system of control that will allow work involving possible sources of ignition to be carried out safely, eliminating the danger of fire to surrounding areas in accordance with NYS Fire Code Chapter 26, OSHA laws and good practices. Policy A Hot Work permit will be required for any activity that requires the use, • Allow only trained and authorized employees to conduct hot work • Ensure permits are used for all hot work outside authorized areas. Employees • Follow all hot work procedures • Properly use appropriate hot work PPE • Inspect all hot work equipment before use• Report any equipment problems • Not use damaged hot work equipment.

Hot Work Procedure Roy Hill. Hot Works Operations Policy Introduction: Purpose To establish procedures defining a system of control that will allow work involving possible sources of ignition to be carried out safely, eliminating the danger of fire to surrounding areas in accordance with NYS Fire Code Chapter 26, OSHA laws and good practices. Policy A Hot Work permit will be required for any activity that requires the use, Permit to Work (PTW) is a key part of managing work activities that have inherently higher risks or unique aspects that could lead to a higher level of risk than routine or daily work activities. It is supported by other management policies, procedures, and processes to regulate all work activities and manage risk. The purpose of this PTW.

PERMIT TO WORK PROCEDURE Pages - Documents

Hot work permit procedure pdf

A. PURPOSE AND SCOPE FOR HOT WORK PERMIT PROCESS. Hot Work Permit. Permit No. This permit must be completed for all cutting, welding and other hot work performed outside a dedicated workshop area. The permit must be displayed at the work site and returned to the authorised site representative on completion of work for sign off and filing. Application for hot work Company/Dept Performing Work A Permit to Work system is a key element of the BP Group Defined Practice for Control of Work and the BP Golden Rules of Safety. It is a formal documented system used t o control certain types of non-routine work which are defined as being hazardous. This procedure sets out a required approach to safely.

Hot work permit procedure pdf


A. PURPOSE AND SCOPE FOR HOT WORK PERMIT PROCESS 1. PURPOSE: The purpose of this program is to establish written procedures to prevent fires resulting from any temporary operation involving open flames or producing heat and/or sparks, as required by OSHA 29 CFR Warning! hot work permit. All temporary operations involving open flames or producing heat and/or sparks require a Hot Work Permit. This includes, but is not limited to, Brazing, Cutting, Grinding, Welding, Thawing, and Soldering.

HS820 Permit To Work Procedure Page 1 of 9 Version: 1.4 Effective 21 March 2016 HS820 Permit To Work Procedure Policy Hierarchy link . Work Health and Safety Act 2011 Work Health and Safety Regulation 2011 Work Health and Safety Policy . Responsible Officer . Director, UNSW Safety and Sustainability . Contact Officer . Manager, UNSW Health & Safety . Supersed ed Documents • FM OHS … UAF Hot Work Permit Procedures Page 1 Revised 11-6-14 Procedure for Contractor Hot Work Permits Policy: A Hot Work Permit is required whenever a contractor or UA Employee is performing hot work within 35 feet of an existing occupied UA facility.

Chapter 12 Fire Prevention Hot Work Procedures . 30 September 2019 SLAC-I-730-0A12C-001-R005 2 of 3 . 2.1 Temporary Hot Work Permit Procedure Temporary hot work … HS820 Permit To Work Procedure Page 1 of 9 Version: 1.4 Effective 21 March 2016 HS820 Permit To Work Procedure Policy Hierarchy link . Work Health and Safety Act 2011 Work Health and Safety Regulation 2011 Work Health and Safety Policy . Responsible Officer . Director, UNSW Safety and Sustainability . Contact Officer . Manager, UNSW Health & Safety . Supersed ed Documents • FM OHS …

See Appendix #1 for Sample Hot Work Permit. Person Performing Hot Work. The person doing the Hot Work must verify that a hot work permit is in place before starting Hot Work. The permit is issued for one location only and is valid for no longer than 24 hours. It may become invalid if conditions change (i.e. adverse environmental condition). This procedure is to be read in conjunction with the Work Permit System. Hot Work is defined as any work which involves the use of tools, equipment or techniques that could generate heat of sufficient intensity to ignite flammable gases, liquids, dusts or materials.

PERMIT TO WORK PROCEDURE Only the central authority, at a time, can issue permits to allow personnel working in hazardous area. Objective Only personnel involved in the task and covered by the permit can enter the area. All personnel concerned are made aware of the hazards involved and measure to be taken. Auditing Compliance with Work Permit Procedures Steven P. Pereira, CSP OSHA requires most companies to implement procedures for controlling hazardous energy (Lockout/Tagout), Confined Space Entry and Hot Work. The OSHA Permit Required Confined Space Entry Standard 1910.146 requires an annual review of the program using cancelled permits. The

Generator’s Permit to Work Code of Practice. This Manual outlines the key elements of this system such as roles and responsibilities, procedures, training, reporting and monitoring activities. Copies of this company-wide manual are available at each CS Energy site. It is also included on No hot work is permitted without authorization, in the form of a signed hot work permit. This This permit will be valid for a maximum of one shift, or eight hours, whichever is shorter.

of a Hot Work Permit, obtained from SNL/NM Department of Building and Fire Safety ; Post the Hot Work Permit in a conspicuous location at the hot work site ; Ensure that prior to requesting a Hot Work Permit for hot work in high hazard areas (e.g., explosives, flammable combustible gases/liquids, radiological), the job and site is This procedure is to be read in conjunction with the Work Permit System. Hot Work is defined as any work which involves the use of tools, equipment or techniques that could generate heat of sufficient intensity to ignite flammable gases, liquids, dusts or materials.

hot work procedure Page 4 Free Document Search Engine

Hot work permit procedure pdf

Hot Work csbp.com.au. Permit to Work (PTW) is a key part of managing work activities that have inherently higher risks or unique aspects that could lead to a higher level of risk than routine or daily work activities. It is supported by other management policies, procedures, and processes to regulate all work activities and manage risk. The purpose of this PTW, Hot Work Procedure . 1. Purpose 1.1. To comply with the standards listed in Section 13 and to outline the safeguards, which shall be taken to achieve safe work conditions before performing hot work activities. This procedure is to protect personnel and property by preventing fires and explosions. 2. Scope 2.1. The Hot Work Procedure applies to.

Reviewed DD Month Year Hot Work Procedures

PROCEDURE 4.0 HOT WORK PROGRAM Hamilton College. Insufficient monitoring of the work permit system. Guidance relating to permit to Work Systems. The following HSE publications can be used as guidance material relating to safety issues surrounding permit to work systems: HS(G)5 Hot work : welding and cutting on plant containing flammable materials, HSE (Not in current HSE list)., Appendix R – Standard Operating Procedure for Hot Works University of Minnesota, Facilities Management November 2002 (Revised: December 2006) Page 3 of 15 5.1. After the final check, Part 2 of the permit shall be filed at the same location as Part 1..

A. PURPOSE AND SCOPE FOR HOT WORK PERMIT PROCESS 1. PURPOSE: The purpose of this program is to establish written procedures to prevent fires resulting from any temporary operation involving open flames or producing heat and/or sparks, as required by OSHA 29 CFR upon work procedures. This prevents instructions from being missed, forgotten or misinterpreted. It also serves as a checklist to ensure that all hazards, protective measures, work procedures and general requirements are reviewed with and understood by the assigned worker(s). A work permit …

630 West 168 Street, Mail Box 8; New York, NY 10032 Tel. (212) 305-6780 Fax (212)795-5847 3 HOT WORK PERMIT PROCEDURES A. PURPOSE: This program establishes the minimum safe working procedures and guidelines for the operation Hot Works Operations Policy Introduction: Purpose To establish procedures defining a system of control that will allow work involving possible sources of ignition to be carried out safely, eliminating the danger of fire to surrounding areas in accordance with NYS Fire Code Chapter 26, OSHA laws and good practices. Policy A Hot Work permit will be required for any activity that requires the use

All hot work is by permit only. Prior to hot work, the HW authorising officer must document on the permit: • the date of the hot work; • the permit expiry time; and • the control measures that were identified during the risk assessment. The type of hot work and the control measures are included in sections 1 to 15 of the hot work permit • Allow only trained and authorized employees to conduct hot work • Ensure permits are used for all hot work outside authorized areas. Employees • Follow all hot work procedures • Properly use appropriate hot work PPE • Inspect all hot work equipment before use• Report any equipment problems • Not use damaged hot work equipment

of a Hot Work Permit, obtained from SNL/NM Department of Building and Fire Safety ; Post the Hot Work Permit in a conspicuous location at the hot work site ; Ensure that prior to requesting a Hot Work Permit for hot work in high hazard areas (e.g., explosives, flammable combustible gases/liquids, radiological), the job and site is Hot Works Operations Policy Introduction: Purpose To establish procedures defining a system of control that will allow work involving possible sources of ignition to be carried out safely, eliminating the danger of fire to surrounding areas in accordance with NYS Fire Code Chapter 26, OSHA laws and good practices. Policy A Hot Work permit will be required for any activity that requires the use

Permit to Work (PTW) is a key part of managing work activities that have inherently higher risks or unique aspects that could lead to a higher level of risk than routine or daily work activities. It is supported by other management policies, procedures, and processes to regulate all work activities and manage risk. The purpose of this PTW All Hot Work must be performed by competent and authorised persons who have received: Awareness training of the hazards and precautions associated with Hot Work (a 21-minute video “Hot Work Risks” is available from the Safety Office), Instruction in the Standard Operating Procedures and application of the Permit-to-Work procedure.

PERMIT TO WORK SYSTEM File ref: OSH047/92460 Version: 5.4 Issue date: July 2017 Page 4 of 10 Table 1: Permit to Work types KPA PERMITS are Compulsory for the following prohibited activities. All Vessels in Port Waters Third Party Contractors KPA jurisdiction KPA Works Bunkering Permit Hot Work Permit All Hot Work must be performed by competent and authorised persons who have received: Awareness training of the hazards and precautions associated with Hot Work (a 21-minute video “Hot Work Risks” is available from the Safety Office), Instruction in the Standard Operating Procedures and application of the Permit-to-Work procedure.

PERMIT TO WORK PROCEDURE Only the central authority, at a time, can issue permits to allow personnel working in hazardous area. Objective Only personnel involved in the task and covered by the permit can enter the area. All personnel concerned are made aware of the hazards involved and measure to be taken. Safe Operating Procedure (Revised 10/17) HOT WORK PERMIT OPERATIONS _____ Authority . In recognition of the inherent hazards posed by certain hot work processes, the National Fire Protection Agency adopted Standard 51B, Standard for Fire Prevention During

4 Issuance of Hot work permit: 4.1 The permit issuer will verify, evaluate, and meter test the work to be conducted with the person doing the work or his supervisor. 4.2 The issuer will survey the work location to verify that conditions meet acceptable permit requirements. (See permit) No Hot Work will be performed in buildings Appendix R – Standard Operating Procedure for Hot Works University of Minnesota, Facilities Management November 2002 (Revised: December 2006) Page 3 of 15 5.1. After the final check, Part 2 of the permit shall be filed at the same location as Part 1.

Hot Work Permit. Permit No. This permit must be completed for all cutting, welding and other hot work performed outside a dedicated workshop area. The permit must be displayed at the work site and returned to the authorised site representative on completion of work for sign off and filing. Application for hot work Company/Dept Performing Work The hot work permit helps the permit authorizing individual, hot work operator, and fire watch recognize potential hazards. Areas can be protected with the use of welding pads, blankets, or curtains, clearing combustibles from a 35-foot radius space around the hot work, or moving the hot work …

upon work procedures. This prevents instructions from being missed, forgotten or misinterpreted. It also serves as a checklist to ensure that all hazards, protective measures, work procedures and general requirements are reviewed with and understood by the assigned worker(s). A work permit … Auditing Compliance with Work Permit Procedures Steven P. Pereira, CSP OSHA requires most companies to implement procedures for controlling hazardous energy (Lockout/Tagout), Confined Space Entry and Hot Work. The OSHA Permit Required Confined Space Entry Standard 1910.146 requires an annual review of the program using cancelled permits. The

630 West 168 Street, Mail Box 8; New York, NY 10032 Tel. (212) 305-6780 Fax (212)795-5847 3 HOT WORK PERMIT PROCEDURES A. PURPOSE: This program establishes the minimum safe working procedures and guidelines for the operation C-17. Hot Work Permit Procedure I. Purpose This procedure provides guidance for persons, including the Operational Technical Support (OTS) contractor, subcontractors, their lower-tier contractors, and NCI-Frederick representatives, who manage, supervise, and perform hot work. II. Scope

All hot work is by permit only. Prior to hot work, the HW authorising officer must document on the permit: • the date of the hot work; • the permit expiry time; and • the control measures that were identified during the risk assessment. The type of hot work and the control measures are included in sections 1 to 15 of the hot work permit Permit to Work (PTW) is a key part of managing work activities that have inherently higher risks or unique aspects that could lead to a higher level of risk than routine or daily work activities. It is supported by other management policies, procedures, and processes to regulate all work activities and manage risk. The purpose of this PTW

PERMIT TO WORK SYSTEM File ref: OSH047/92460 Version: 5.4 Issue date: July 2017 Page 4 of 10 Table 1: Permit to Work types KPA PERMITS are Compulsory for the following prohibited activities. All Vessels in Port Waters Third Party Contractors KPA jurisdiction KPA Works Bunkering Permit Hot Work Permit Managers shall train employees on departmental Hot Work Permit procedures and specific safety procedures for the type of hot work equipment used. This training shall be completed upon initial assignment and cover the following subjects: • Safety procedures specific to the equipment used. • Required personal protective equipment for job tasks. • Identification of Permit Authorizing

HOT WORK PERMIT CHECKLIST csum.edu

Hot work permit procedure pdf

Permit Program For Hot Work Operating Procedures. Safety Tips from the WorkSafe People Sample Framework for a Hot Work Permit Program* (Name of Company) (Date) Purpose . The purpose of this program is to establish safe procedures for conducting Hot Work tasks. It includes, but is not limited to: brazing, cutting, grinding, soldering, thawing pipe, torch-applied roofing and welding. Scope, ensuring that safe hot work procedures are followed, so it is essential that those who issue permits to work or carry out associated analysis or environmental monitoring are competent to do so. The information that should be contained in a permit to work for hot work will depend on the job to be done. Generally it should include:.

Auditing Compliance with Work Permit Procedures. Before hot work can commence the work site must be certified gas free. Confirm certificate has been issued. 10. ENTRY PERMIT An entry permit must be obtained before entry is permitted into a confined space. Confirm Entry Permit has been issued., • Allow only trained and authorized employees to conduct hot work • Ensure permits are used for all hot work outside authorized areas. Employees • Follow all hot work procedures • Properly use appropriate hot work PPE • Inspect all hot work equipment before use• Report any equipment problems • Not use damaged hot work equipment.

PPT – Hot Work Permits Policy Procedures PowerPoint

Hot work permit procedure pdf

Safety Tips from the WorkSafe People AF Group. 4 Issuance of Hot work permit: 4.1 The permit issuer will verify, evaluate, and meter test the work to be conducted with the person doing the work or his supervisor. 4.2 The issuer will survey the work location to verify that conditions meet acceptable permit requirements. (See permit) No Hot Work will be performed in buildings 630 West 168 Street, Mail Box 8; New York, NY 10032 Tel. (212) 305-6780 Fax (212)795-5847 3 HOT WORK PERMIT PROCEDURES A. PURPOSE: This program establishes the minimum safe working procedures and guidelines for the operation.

Hot work permit procedure pdf

  • PERMIT TO WORK SYSTEM Kimberley Ports Authority
  • Hot Works Operations Policy ESF
  • SAFETY & HEALTH

  • Auditing Compliance with Work Permit Procedures Steven P. Pereira, CSP OSHA requires most companies to implement procedures for controlling hazardous energy (Lockout/Tagout), Confined Space Entry and Hot Work. The OSHA Permit Required Confined Space Entry Standard 1910.146 requires an annual review of the program using cancelled permits. The Generator’s Permit to Work Code of Practice. This Manual outlines the key elements of this system such as roles and responsibilities, procedures, training, reporting and monitoring activities. Copies of this company-wide manual are available at each CS Energy site. It is also included on

    Insufficient monitoring of the work permit system. Guidance relating to permit to Work Systems. The following HSE publications can be used as guidance material relating to safety issues surrounding permit to work systems: HS(G)5 Hot work : welding and cutting on plant containing flammable materials, HSE (Not in current HSE list). Hot Work Permit. Permit No. This permit must be completed for all cutting, welding and other hot work performed outside a dedicated workshop area. The permit must be displayed at the work site and returned to the authorised site representative on completion of work for sign off and filing. Application for hot work Company/Dept Performing Work

    down procedures. 2.3 Hot work permits should not be issued without considering the significance of any other permits to work in the vicinity or adjacent manufacturing processes. 2.4 Hot work permit should be issued for a specific task that is to be undertaken in a clearly identified area. 3. Before Hot Work … A. PURPOSE AND SCOPE FOR HOT WORK PERMIT PROCESS 1. PURPOSE: The purpose of this program is to establish written procedures to prevent fires resulting from any temporary operation involving open flames or producing heat and/or sparks, as required by OSHA 29 CFR

    Permit to Work (PTW) is a key part of managing work activities that have inherently higher risks or unique aspects that could lead to a higher level of risk than routine or daily work activities. It is supported by other management policies, procedures, and processes to regulate all work activities and manage risk. The purpose of this PTW STANDARD OPERATING PROCEDURE FOR HOT WORKS Revised Date: May 2012 PURPOSE: This Hot Work Permit is required for any temporary operation involving open flames or producing heat and/or sparks. This includes, but is not limited to, oxyacetylene cutting, hot riveting, grinding, chipping, soldering, brazing, thawing pipe, torch- applied roofing or flooring, and welding. The permit is intended

    Generator’s Permit to Work Code of Practice. This Manual outlines the key elements of this system such as roles and responsibilities, procedures, training, reporting and monitoring activities. Copies of this company-wide manual are available at each CS Energy site. It is also included on STANDARD OPERATING PROCEDURE FOR HOT WORKS Revised Date: May 2012 PURPOSE: This Hot Work Permit is required for any temporary operation involving open flames or producing heat and/or sparks. This includes, but is not limited to, oxyacetylene cutting, hot riveting, grinding, chipping, soldering, brazing, thawing pipe, torch- applied roofing or flooring, and welding. The permit is intended

    Hot Works Operations Policy Introduction: Purpose To establish procedures defining a system of control that will allow work involving possible sources of ignition to be carried out safely, eliminating the danger of fire to surrounding areas in accordance with NYS Fire Code Chapter 26, OSHA laws and good practices. Policy A Hot Work permit will be required for any activity that requires the use Chapter 12 Fire Prevention Hot Work Procedures . 30 September 2019 SLAC-I-730-0A12C-001-R005 2 of 3 . 2.1 Temporary Hot Work Permit Procedure Temporary hot work …

    Warning! hot work permit. All temporary operations involving open flames or producing heat and/or sparks require a Hot Work Permit. This includes, but is not limited to, Brazing, Cutting, Grinding, Welding, Thawing, and Soldering. Appendix R – Standard Operating Procedure for Hot Works University of Minnesota, Facilities Management November 2002 (Revised: December 2006) Page 3 of 15 5.1. After the final check, Part 2 of the permit shall be filed at the same location as Part 1.

    This procedure is to be read in conjunction with the Work Permit System. Hot Work is defined as any work which involves the use of tools, equipment or techniques that could generate heat of sufficient intensity to ignite flammable gases, liquids, dusts or materials. STANDARD OPERATING PROCEDURE FOR HOT WORKS Revised Date: May 2012 PURPOSE: This Hot Work Permit is required for any temporary operation involving open flames or producing heat and/or sparks. This includes, but is not limited to, oxyacetylene cutting, hot riveting, grinding, chipping, soldering, brazing, thawing pipe, torch- applied roofing or flooring, and welding. The permit is intended

    See Appendix #1 for Sample Hot Work Permit. Person Performing Hot Work. The person doing the Hot Work must verify that a hot work permit is in place before starting Hot Work. The permit is issued for one location only and is valid for no longer than 24 hours. It may become invalid if conditions change (i.e. adverse environmental condition). 4 Issuance of Hot work permit: 4.1 The permit issuer will verify, evaluate, and meter test the work to be conducted with the person doing the work or his supervisor. 4.2 The issuer will survey the work location to verify that conditions meet acceptable permit requirements. (See permit) No Hot Work will be performed in buildings

    Hot Work Permit. Permit No. This permit must be completed for all cutting, welding and other hot work performed outside a dedicated workshop area. The permit must be displayed at the work site and returned to the authorised site representative on completion of work for sign off and filing. Application for hot work Company/Dept Performing Work 4 Issuance of Hot work permit: 4.1 The permit issuer will verify, evaluate, and meter test the work to be conducted with the person doing the work or his supervisor. 4.2 The issuer will survey the work location to verify that conditions meet acceptable permit requirements. (See permit) No Hot Work will be performed in buildings

    C-17. Hot Work Permit Procedure I. Purpose This procedure provides guidance for persons, including the Operational Technical Support (OTS) contractor, subcontractors, their lower-tier contractors, and NCI-Frederick representatives, who manage, supervise, and perform hot work. II. Scope 6.0 Hot Work Permit Procedures 6.1 Preparation of work area—before a hot work permit is approved and issued, the Hot Work Supervisor shall verify that: a. All welding and cutting equipment to be used is in satisfactory condition and in good repair. b. Any combustible materials …

    All hot work is by permit only. Prior to hot work, the HW authorising officer must document on the permit: • the date of the hot work; • the permit expiry time; and • the control measures that were identified during the risk assessment. The type of hot work and the control measures are included in sections 1 to 15 of the hot work permit No hot work is permitted without authorization, in the form of a signed hot work permit. This This permit will be valid for a maximum of one shift, or eight hours, whichever is shorter.

    Warning! hot work permit. All temporary operations involving open flames or producing heat and/or sparks require a Hot Work Permit. This includes, but is not limited to, Brazing, Cutting, Grinding, Welding, Thawing, and Soldering. Generator’s Permit to Work Code of Practice. This Manual outlines the key elements of this system such as roles and responsibilities, procedures, training, reporting and monitoring activities. Copies of this company-wide manual are available at each CS Energy site. It is also included on